View All Products
CPP Product Line
CPP Sprayliner
Structural Epoxy
Coating / Liner
A high strength, applied and bonded lining solution for wastewater infrastructure, large diameter tanks, and large wall interior lining requirements. Spray-applied, ultra-high build, 100% solids, structural-grade epoxy coating and lining system. An advanced microfiber-reinforced polymer (FRP) technology cured with enhanced mechanical properties. Optimized with polycyclic curing agents for increased crosslinking with excellent H2S resistance, sealing, moisture tolerance, UV stabilization, and service wear durability.
For use as an applied liner in moderate and severe WWTP environments infrastructure (including closed, partially-open, and open tanks).
CPP Sprayliner MH
Structural Epoxy
Coating / Liner
A high strength, applied and bonded lining solution for sanitary sewer collection system lining requirements to seal inflow and infiltration (I&I) while protecting against corrosion. Spray-applied, ultra-high build, 100% solids, structural-grade epoxy coating and lining system. An advanced microfiber-reinforced polymer (FRP) technology cured with enhanced mechanical properties. Optimized with polycyclic and amine blended curing agents for increased crosslinking with excellent H2S resistance, sealing, moisture tolerance, and service wear durability.
For use as an applied liner in sanitary sewer collection environments (including manholes, lift stations, and pipe).
CPP Sprayliner 61
Structural Epoxy
Coating / Liner
A high strength, applied and bonded lining solution for potable water storage infrastructure, large diameter tanks, and large wall interior lining requirements. Spray-applied, ultra-high build, 100% solids, structural-grade epoxy coating and lining system for potable water use. An advanced microfiber-reinforced polymer (FRP) technology cured with enhanced mechanical properties. Optimized with polycyclic curing agents for increased crosslinking with excellent corrosion resistance, sealing, moisture tolerance, UV stabilization, and service wear durability.
Underwriters Laboratories Inc.® classified to ANSI/NSF Standard 61, and the extraction requirements of NSF/ANSI/CAN 600 for use as an applied liner in potable water storage.
CPP Trowel-Liner
Structural Epoxy
Coating / Liner
Trowel-applied, ultra-high build, 100% solids, structural-grade amine epoxy compound. An advanced microfiber-reinforced polymer (FRP) technology cured with enhanced mechanical properties. A high strength, applied and bonded solution for water and wastewater infrastructure interior lining requirements. Formulated for H2S resistance, sealing, moisture tolerance, UV stabilization, and service wear durability.
For use in WWTP and sanitary sewer environments; formulated also for service in potable water environments – Underwriters Laboratories Inc.® classified to ANSI/NSF Standard 61, and the extraction requirements of NSF/ANSI/CAN 600 for use in potable water storage.
MORTARTEC Product Line
Mortartec Cladliner
Epoxy Cement
Coating / Liner
Mortartec Cladliner is an engineered hybrid epoxy-cement liner combining the simplicity of a cementitious lining with the performance of a high build epoxy, all in one product. Mortartec Cladliner offers acid resistance to protect from corrosion derived from mild-to-moderate hydrogen sulfide (H2S) conditions. This is accomplished by combining epoxy polymerization with a formulated balance of of Portland cement, high density graded silica aggregate, and synthetic fibers. Cladliner serves as a resurfacer and liner, all-in-one.
Designed for protective lining of concrete, brick, masonry sanitary sewer manholes and domestic wastewater collection system assets. Lining solution for mild-to-moderate corrosive WWTP structures.
Mortartec Ceramico
Epoxy Cement
Repair / Resurfacer
An epoxy-modified mortar incorporating cutting-edge epoxide technology combined with a specific balance of Portland cement, high density graded silica aggregate, and synthetic fibers to produce one of the most coveted epoxy mortars in the industrial market today for surfacing, patching and filling voids and bugholes in concrete substrate. Designed to take early topcoats of epoxy coatings without the need for further preparation. Mortartec Ceramico has the unique ability to be applied both thin and thick by hand or by spray application, typically from 1/16” to 3/4” (1.6 to 19 mm) in depth. Exhibits excellent performance properties unlike any mortar technology before it with incredible adhesive properties, enhanced barrier sealing capabilities assisting with minimizing outgassing.
Mortartec Silicate
Microsilica Cement
Repair / Resurfacer
Industrial-grade blend of Portland cement, graded silica sand, fibers and silica fume. The mortar may be hand or spray applied, typically from ½” to 2” (12.7 to 50.8 mm) in depth. Uses include repairing concrete walls, ceilings, repairing and lining brick or concrete infrastructure. Mortartec Silicate provides an extremely dense matrix and will accept top coatings at earlier stages than typical Portland cement repair products.
Hydrxx-1
Water Stop Hydraulic Cement
Repair
Quick setting (60 to 90 seconds) industrial-grade hydraulic cement compound designed for structural patching and as a leak stopper and water plug. Designed to instantly stop low-pressure running water and/or seepage through brick, concrete or other masonry walls and floors.
Hydrxx-3
Water Stop Hydraulic Cement
Repair
Quick setting (3 to 5 minutes) industrial-grade hydraulic cement compound designed for structural patching and as a leak stopper and water plug. Designed to instantly stop low-pressure running water and/or seepage through brick, concrete or other masonry walls and floors.
Other Products
Uroseal Product Line
Uroseal 45V
Elastomeric Sealant
100% solids elastomeric sealant. Formulated for vertical and overhead applications requiring high build elastomeric coating or joint sealing. Uroseal 45V is ideally suited for both indoor and outdoor applications and can bond to concrete and steel. Uroseal 45V produces a flexible, long-lasting sealant with superior adhesion, cohesion, and elasticity that resists deterioration caused by weathering, stress, movement, and gases. Often used as a joint system in non-immersive sanitary sewer or wastewater vapor pits, manholes and collection system pipe.
Primecoat Product Line
SE-d Primecoat
Primer
Two-component polyamine penetrating epoxy primer and sealer for concrete. Designed to perform and bond to slightly damp, saturated surface dry (SSD) concrete to assist with an effective barrier in these conditions. SE-d Primecoat promotes sealing allowing subsequent early top coating, while facilitating in the mitigation of low moisture vapor transmission (MVT), outgassing, and chemical penetration. SE-d Primecoat’s low viscosity allows for deep penetration to form a suitably strong base for subsequent topcoats of grouts, mortars, and other coating and lining systems.
Uroflex Product Line
Uroflex
This product has been discontinued. Please contact your local sales representative for further assistance.
Coating / Liner
High build, 100% solids, hybrid coating/lining system specifically designed for domestic wastewater treatment environments. Uroflex is applicator friendly and easy to apply; conveniently produced as a one-to-one mix ratio by volume. Uroflex is formulated as a hybrid urethane-modified epoxy (UME) enhancing its epoxy film flexibility and crosslinking for added protection. Uroflex is formulated to protect within immersive wastewater environments requiring a semi-rigid protective film against hydrogen sulfide (H2S) attack.
Uroflex 61
This product has been discontinued. Please contact your local sales representative for further assistance.
Coating / Liner
High build, 100% solids, hybrid coating/lining system specifically designed for potable water storage environments. Uroflex 61 is applicator friendly and easy to apply; conveniently produced as a one-to-one mix ratio by volume. Uroflex 61 is formulated as a hybrid urethane-modified epoxy (UME) enhancing its epoxy film flexibility and crosslinking for added protection. Uroflex 61 is formulated to protect within immersive potable water environments requiring a semi-rigid protective film.
Formulated for service in potable water environments – Underwriters Laboratories Inc.® classified to ANSI/NSF Standard 61, and the extraction requirements of NSF/ANSI/CAN 600 for use in potable water storage.