Uroflex HCN
Product Description
Download Name | Link |
---|---|
Product Data Sheet | Download |
Features
Product Applications
Uroflex HCN meets these Requirements:
Uroflex HCN has been proven in many aggressive enclosed, immersive, and partially opened environments. Uroflex performs in areas subject to high chemical attack.
Ideally suited as a protective coating/lining solution for:
- Industrial structures, tanks, vessels, etc.
- Primary and secondary containment
- Seamless and sealed coating & lining
- Protection against chemicals for steel and concrete
- Other industrial lining and coating applications
The success of any coating application is directly proportional to the completeness of the substrate preparation and the care the application crew puts into the application. Surface must be clean and sound. Remove all dust, contaminants, grease, curing compounds, rust, impregnation, waxes, foreign particles, and disintegrated materials from the surface, in order to achieve a clean and profiled surface.
Concrete: Prepare the concrete by abrasive blasting, high pressure water cleaning, and/or approved mechanical method to achieve clean, sound, and profiled concrete. Prepare concrete in accordance with SSPC-SP 13/NACE No. 6. “Surface Preparation of Concrete.”Although priming is not required, in some cases when suspecting excessive moisture vapor transmission (MVT), out-gassing, or other impediments – an Epoxytec recommended primer may be considered. Steel: Before preparing steel, please inspect and remove oil, grease, or other contaminants – “Solvent Cleaning” (SSPC-SP1) may be required. Remove all sharp peaks, including weld spatter. Abrasive blasting (or other approved mechanical methods) must be used in order to achieve a clean surface with a minimum profile of 3 mils. Stripe coat all edges and peaks with an Epoxytec recommended primer. To prevent flash rusting, consider the use of an Epoxytec recommended primer.
Mix part A with part B. Proportion the components into a clean pall and mix for approximately 5 minutes with a “jiffy mixer” (or equivalent electric drill), on a low speed (400-600 rpm) drill until the color is uniform blend. When possible, Epoxytec recommends Uroflex HCN as a two-coat system. NOTE: If spraying, Epoxytec recommends at minimal the use of a .023” orifice spray tip or greater, 64:1 ratio spray pump or greater, 3/8” hoses, with 1/4” whip.
Uroflex HCN can be a single coat or multiple coat system. Uroflex HCN can be applied onto a cementitious surface at 16 mils (minimum) to 30 mils (maximum by roller/brush) or 65 mils (maximum by spray) per coat at 77F. For a total coating thickness exceeding 30 mils (by roller/brush) or 65 mils (by spray), multiple coats are necessary. Uroflex HCN can be applied onto a metallic surface at 10 mils (minimum) to 16 mils (maximum by roller/brush) or 30 mils (maximum by spray) per coat at 77F. For a total coating thickness exceeding 16 mils (by roller/brush) or 30 mils (by spray), multiple coats are necessary.
Storage & Handling | Shelf life: 14 months, sealed. Store in a dry area away from direct sunlight. The material should be conditioned to between 65º F and 85º F before use. |
---|---|
Finish | Gloss |
Mix Ratio | 3:1 (by volume) |
Product Type | Aliphatic polyamine novolac |
Soilds by Volume ASTM D2697U | 100% |
Solvent VOC | none |
POT Type | 30 min. (25 C / 200 g mass) |
Compressive Strength | 12,200 psi |
Viscosity Mixed | 2,500 cps @ 25 C |
Adhesion Strength (Steel) | 2,000 psi |
Water Absorption | < 0.1 g/sq.m. |
Tensile Strength | 9,900 psi |
Hardness | 70 |
Complete Cure | 48 hours (25 C) |
Operational Temperature | 40F ‐ 120F |
Temperature Exposure (Dry) | 0F ‐ 160F |
Temperature Exposure (Wet) | 0F ‐ 147F |
Uroflex HCN
Epoxytec Uroflex HCN is a 100% solid, medium to high build, novolac epoxy coating and liner.
Uroflex HCN is is an ultra-high cross-link, aliphatic polyamine novolac epoxy, formulated for ultra high chemical resistance. The material is often utilized to combat solvents, hydrocarbons, and various chemicals or volatiles often found in containment or secondary catch basins. As a primary liner, it can withstand industrial immersion applications and ultra-harsh environments.